A New Way To Support SplatSpace!

If you’ve been wanting to support Splat Space and you buy stuff on Amazon, then now you can combine the two! Splat Space is now part of the Amazon Smile initiative, which donates 5% of your purchase to Splat Space! So if your an avid Amazon shopper, why not support your favorite local maker space at the same time! Visit the Donate page for more ways to donate, or just click on the image below to get started.

Amazon Smile

  1. Click on the image above or this link: https://smile.amazon.com/ch/27-3411181
  2. Confirm and agree to making “durham-makerspace” their charity
  3. Bookmark smile.amazon.com as the place to go before shopping for something or use a browser plugin or magic gizmo or whatever to insure they’re within that subdomain at the point they purchase something.

 

Notes from Nation of Makers Meeting

On August 24th Splatspace sent a delegate to the Nation of Makers Meeting at the White House. Almost 200 delegates from private and public makerspaces around the country met to discuss best practices and brainstorm solutions to common problems. 
This is Part I: a recap of notes taken during the morning session of Lightning Talks from prominent makerspace organizers and government officials. It’s arranged very loosely by topics that we feel are of interest to anyone involved in the creation or running of a makerspace or hackerspace. Part II will be coming soon, specifically focusing on the issue of diversity and “inclusion by design.”

Burnout: burnout is common in makerspaces. It does not come from “doing too much,” but from not feeling accomplished; putting in effort for too long with no perceived reward or acknowledgement. Too many small projects without recognition leave people apathetic. Apathy is contagious; don’t let it poison your environment. Slumps, especially post-event slumps, can become routines.

Big events and “big scores” inspire. Plan  and participate in big public events. DOCUMENT and PUBLICIZE them. Much like scientific research, if events aren’t published to the larger community, “they never happened.”

A Space’s “Open Hours” only bring in established “makers” rather than broaden your appeal and bring in new people. Consistent, Reliable, Focused Meetups attract people who have an interest in that particular skill or event who would never come to an Open Meeting or Open Hours. We’ve seen this very recently with the “Saturday Sewcialist Party” at Splatspace; it was intended to be a one-shot introduction to the Space’s sewing machines and immediately turned into a well-attended and growing weekly event. 

If members have a skill, encourage them to share it in an event. Offer them help if they don’t know how to host or prep an event; just because they have a skill or a set of skills doesn’t mean that they automatically have any idea of how to create an event to share it. 

Once enough interest is demonstrated, a meetup needs to be CONSISTENT: scheduled at a predictable time. It’s not necessarily weekly, it may be semi-weekly or monthly, but it has to be something at a consistent day and time that interested parties can plan for. A moving target is going to lose its attendees.

A meetup has to be FOCUSED: something vague like “crafts” might bring in someone who thinks of themselves as a “crafter,” but not others. A papermaking meetup will bring in anyone curious about papermaking because it speaks directly to them, and once they’re in, they can meet and cross-pollinate with others. Also, focused meetups may end up rescuing abandoned groups; your makerspace can attract attendees from former groups that died out for lack of support or a space to meet. 

A meetup has to be RELIABLE: if the host cannot host it, they have to have a backup plan/ backup host. Put that in place as part of the event planning so there’s no last-minute panic. 

Attracting New members: it’s important to INVITE potential members that you run into. Don’t just give them your Space’s information, actually say the words and invite them. Make it clear that newbies are welcome; it’s always a bit awkward to walk into a new situation where most of the people already know each other. You may want to have specific persons who are good at making others feel welcome fill the role of a new-member facilitator.

Once you have new members: give them a stake in the organization. Inspire them with other members’  projects and stories, but also get them to share the load. Actively recruit them into events and give them Space duties. In this, you have to lead by example.

In the next post we should be discussing the vital topics of increasing makerspace diversity and designing a makerspace to promote inclusion.

Homemade Single String Electric Guitar

maxresdefaultSplatSpace member, Jeff, had a spare ski and decided to do something very unusual with it. Taking inspiration from the Berimbau instruments used in Capoeira, he decided to turn his ski into a single string guitar. Aside from the ski and the wire from a car tire, he also used custom 3D printed parts and hard drive magnets to make it electric. So how does it sound? I could describe it here, but it’d be easier if you just watch the video below 🙂

 

DurHam fest tomorrow!

di8ozazXTAlthough the name sounds delicious, the Durham Hamfest is actually about amateur radio enthusiasts and not about actual ham. So if you’re into amateur radios and want something to do this weekend, the Durham FM Association’s computers & electronics swapmeet and amateur radio testing & licensing festival (DurHamFest) is happening on Saturday, from 8:30 am to 12:30 pm at Durham Public Schools Staff Development Center at 2107 Hillandale Road Durham

Awesome wood working projects

20160517_191755SplatSpace member C.J. is a longtime woodworking maker that likes to mix creative engineering/design with woodcraft. This past Tuesday, he brought in a few samples of his work. the first example is a custom parrot puzzle that he designed by hand, transferred to wood, and cut out using a scroll saw. It’s designed in such a way that it, once it’s assembled, it can be picked up by any piece (even the beak) without falling apart.

The second one is a support beam for a drop leaf table. The original metal support beam had been bent and would no longer support the table, so C.J. created a replacement out of wood. The result is more sturdy and longer lasting than the original. You can see what I mean in the pics below.